Macallan Green Marble Tub and Basin

Appearance and Natural Variation

Macallan Green Marble is listed as green marble for indoor use. Review the actual batch for color range, veining, fissures, and any resin treatment before approving its appearance.

Care in Wet Areas

Marble can stain, and acidic cleaners can etch its surface. Ask the fabricator which sealer suits the selected material, then follow the sealer maker’s care and reapplication instructions.

Approve the Fixture Construction

A visually suitable slab does not establish that a tub or basin design is ready to build. Confirm waterproofing and sealing, drain connections, structural support, and local installation requirements with the fabricator and qualified installer.

Freestanding or Built-In Tub

A freestanding tub exposes exterior faces, making vein direction and any visible joints prominent. A built-in design shifts attention to the rim and adjoining surfaces.

Both require drawings showing support, drain location, handling route, and service access for local installation.

Countertop or Integrated Basin

A countertop basin requires coordinated counter cutouts and edge details. An integrated basin concept needs review of bowl geometry, drainage, and how the stone meets the counter.

Show basin and countertop together in the drawings so visible joints can be assessed.

Single or Paired Pieces

A single feature piece allows more freedom in vein placement. Paired pieces call for an approved batch and marked vein direction to establish an agreed visual relationship.

Each finished piece needs a checked access route before its configuration is approved.

Honed or Matte Finish

A honed surface softens reflections and generally makes light scratches less conspicuous. Water can temporarily darken marble or leave marks as it dries.

Honed touch points feel less glossy. Clean with a pH-neutral stone cleaner and dry wet areas; assess traction on a wet sample before specifying exposed surfaces.

Polished Finish

A polished surface emphasizes green color and veining but shows fingerprints, dried water spots, and fine scratches more readily. Its reflective face benefits from prompt wiping after use.

Polished edges can suit visible touch points. Check wet-surface suitability with the project installer rather than assuming the finish provides traction.

Approve the Actual Finish Sample

The approved material sample should show the proposed finish and edge. Inspect it under direct and angled light, add water, then check its appearance after drying.

Other surface treatments require confirmation for this specific marble and fabrication plan.

Set Overall and Internal Geometry

Dimension the tub and basin separately. Show overall length, width, height, bowl depth, slopes, rim width, and usable internal space.

Identify wall or panel construction. The listed 18 mm thickness is a product attribute, not a structural specification for every point.

Locate Plumbing and Detail Joints

Mark drain and overflow centerlines on plan and sections. Include faucet hole locations, spout reach, handle clearance, and access to connections.

Specify edge profiles and visible joints. Show where panels meet and how those joints relate to waterproofing.

Verify Support and Delivery Access

Show the support arrangement and bearing points for the completed units. Have the local designer verify loads against the floor and framing.

Measure doors, corridors, stairs, and lift openings. Confirm the route and handling plan against finished piece dimensions before fabrication.

Review the Actual Batch

A small sample cannot represent every slab. Request current batch photos and a remote video showing full surfaces under consistent lighting.

Green tone, vein density, pores, and natural fissures can vary. Identify any resin-treated areas and agree which visible features are acceptable.

Sign Off the Vein Layout

Tub and basin components should be reviewed together where visual continuity matters. Ask for a marked layout showing vein direction and the face assigned to each visible part.

Before cutting, record the approved batch, acceptable color and vein range, fissure and resin limits, and signed layout. Keep dated photos with the approval.

Pre-Production Approval

Approved shop drawings should identify dimensions, the specified 18 mm thickness, finish, edge details, drain cutouts, and joints.

The selected batch should also be reviewed for color range and natural fissures before cutting.

Checks During Fabrication

Cut pieces should be checked against drawings for dimensions, thickness, edge quality, and drain placement.

Where components meet, a dry lay helps reveal joint misalignment and finish differences before final packing.

Final Inspection and Packing

Final inspection should record finish consistency, visible fissures, treatment where applicable, quantities, and protective packing.

Numbered pieces and matching labels help local installers identify positions; photos or video give buyers a reviewable record before shipment.

Verify Batch Access

Green marble varies in tone and veining. Request current slab video, batch identification, and an approved sample.

STOOANCE supports remote selection and batch reservation. Confirm current availability before ordering.

Review Fabrication Controls

Custom tub and basin drawings should define dimensions, thickness, cutouts, edges, and finish. Require written approval of revisions before cutting.

STOOANCE offers drawing-based fabrication through three specialized stone factories. Match inspection records to the approved drawings.

Check Records and Communication

Packing plans should identify pieces and protect edges. Request inspection photos or video, labels, and packing records before dispatch.

STOOANCE supports piece numbering and labelled packing. Confirm how changes are reported and verify the scope and validity of any requested documentation.

Approve the Actual Batch

Small photos cannot show the full range of green tone, veining, fissures, or resin treatment. Review slab video or full-slab images and approve the selected batch.

Separate batches can vary visibly. Reserve and number pieces when the tub and basin must read as a matched set.

Coordinate Plumbing and Support

Drain and faucet coordinates belong on approved shop drawings, alongside cutouts and connection clearances. Missing offsets can make finished stone difficult to fit.

The listed 18 mm thickness is a product attribute, not a complete structural design. The local installer must review support, waterproofing, handling, and plumbing connections before fabrication is finalized.

Plan Packing and Site Access

Crate dimensions, protection, labels, and unloading method should match the shipment and installation sequence. Confirm doorways, stairs, lifting equipment, and the route to the bathroom before dispatch.

The local installer should check whether the pieces can be moved and positioned safely on site.